**Configuration des vitesses dans le Slicer**
  * Baisser “Wall Speed” à 30 mm/s
  * Baisser “Top/Bottom Speed” à 30 mm/s
  * Augmenter “Travel Speed” à 100 mm/s
  * Baisser “Skirt/Brim Speed” à 25 mm/s
  * Baisser “Print Acceleration”, “Initial Layer Acceleration” et “Skirt/Brim Acceleration” à 300 mm/s
  * Garder “Travel Acceleration” et “Initial Layer Travel Acceleration” à 3'000 mm/s
  * Baisser “Print Jerk”, “Initial Layer Jerk” et “Skirt/Brim Jerk” à 5 mm/s, Garder “Travel Jerk” à 10 mm/s
    * Revient à positionner "Junction Deviation" à 0.03

**Résultat de l'optimisation**
  * Linear Advance, K = 0.47
  * Retraction de 3.2mm à 30mm/s, pas de Z-Hop
  * Print Acceleration = 500
  * Junction Deviation = 0.03

**A repositionner après un M502**
<code>
M92 X80.35 Y80.35 Z398.27 E392.50
M301 P16.44 I1.25 D53.89
M304 P121.66 I22.85 D431.88
M201 X3000.00 Y2000.00 Z60.00 E350.00
M204 P300.00 R500.00 T5000.00
M205 B50000.00 S0.00 T0.00 J0.03
M851 X29.00 Y-15.00 Z-2.25
M900 K0.47
</code>

**Dump complet de l'EEPROM**
<code>
Send: M503
Recv: echo:  G21    ; Units in mm (mm)
Recv: 
Recv: echo:; Filament settings: Disabled
Recv: echo:  M200 S0 D1.75
Recv: echo:; Steps per unit:
Recv: echo: M92 X80.35 Y80.35 Z398.27 E392.50
Recv: echo:; Maximum feedrates (units/s):
Recv: echo:  M203 X500.00 Y500.00 Z6.00 E60.00
Recv: echo:; Maximum Acceleration (units/s2):
Recv: echo:  M201 X3000.00 Y2000.00 Z60.00 E3000.00
Recv: echo:; Acceleration (units/s2): P<print_accel> R<retract_accel> T<travel_accel>
Recv: echo:  M204 P2000.00 R3000.00 T2000.00
Recv: echo:; Advanced: B<min_segment_time_us> S<min_feedrate> T<min_travel_feedrate> J<junc_dev>
Recv: echo:  M205 B50000.00 S0.00 T0.00 J0.30
Recv: echo:; Home offset:
Recv: echo:  M206 X0.00 Y0.00 Z0.00
Recv: echo:; Auto Bed Leveling:
Recv: echo:  M420 S0 Z0.00
Recv: echo:  G29 W I0 J0 Z0.88690
Recv: echo:  G29 W I1 J0 Z0.86179
Recv: echo:  G29 W I2 J0 Z0.94298
Recv: echo:  G29 W I3 J0 Z1.17230
Recv: echo:  G29 W I4 J0 Z1.36229
Recv: echo:  G29 W I0 J1 Z0.88606
Recv: echo:  G29 W I1 J1 Z0.87016
Recv: echo:  G29 W I2 J1 Z1.00659
Recv: echo:  G29 W I3 J1 Z1.16226
Recv: echo:  G29 W I4 J1 Z1.29199
Recv: echo:  G29 W I0 J2 Z0.89276
Recv: echo:  G29 W I1 J2 Z0.85677
Recv: echo:  G29 W I2 J2 Z0.96557
Recv: echo:  G29 W I3 J2 Z1.09949
Recv: echo:  G29 W I4 J2 Z1.23173
Recv: echo:  G29 W I0 J3 Z0.92289
Recv: echo:  G29 W I1 J3 Z0.87937
Recv: echo:  G29 W I2 J3 Z0.96557
Recv: echo:  G29 W I3 J3 Z1.08358
Recv: echo:  G29 W I4 J3 Z1.19071
Recv: echo:  G29 W I0 J4 Z0.95888
Recv: echo:  G29 W I1 J4 Z0.88021
Recv: echo:  G29 W I2 J4 Z0.95637
Recv: echo:  G29 W I3 J4 Z1.04257
Recv: echo:  G29 W I4 J4 Z1.11790
Recv: echo:; Endstop adjustment:
Recv: echo:  M666 Z0.00
Recv: echo:; PID settings:
Recv: echo:  M301 P22.16 I1.95 D63.07
Recv: echo:  M304 P87.81 I12.18 D422.02
Recv: echo:; Z-Probe Offset (mm):
Recv: echo:  M851 X29.00 Y-15.00 Z-2.25
Recv: echo:; Linear Advance:
Recv: echo:  M900 K0.47
Recv: echo:; Filament load/unload lengths:
Recv: echo:  M603 L665.00 U670.00
Recv: echo:; Filament runout sensor:
Recv: echo:  M412 S1
Recv: ok
</code>