Le wiki de Fred

Configuration des vitesses dans le Slicer

• Baisser “Wall Speed” à 30 mm/s
• Baisser “Top/Bottom Speed” à 30 mm/s
• Augmenter “Travel Speed” à 100 mm/s
• Baisser “Skirt/Brim Speed” à 25 mm/s
• Baisser “Print Acceleration”, “Initial Layer Acceleration” et “Skirt/Brim Acceleration” à 300 mm/s
• Garder “Travel Acceleration” et “Initial Layer Travel Acceleration” à 3'000 mm/s
• Baisser “Print Jerk”, “Initial Layer Jerk” et “Skirt/Brim Jerk” à 5 mm/s, Garder “Travel Jerk” à 10 mm/s
  • Revient à positionner “Junction Deviation” à 0.03

Résultat de l'optimisation

• Linear Advance, K = 0.47
• Retraction de 3.2mm à 30mm/s, pas de Z-Hop
• Print Acceleration = 500
• Junction Deviation = 0.03

A repositionner après un M502

M92 X80.35 Y80.35 Z398.27 E392.50
M301 P16.44 I1.25 D53.89
M304 P121.66 I22.85 D431.88
M201 X3000.00 Y2000.00 Z60.00 E350.00
M204 P300.00 R500.00 T5000.00
M205 B50000.00 S0.00 T0.00 J0.03
M851 X29.00 Y-15.00 Z-2.25
M900 K0.47

Dump complet de l'EEPROM

Send: M503
Recv: echo:  G21    ; Units in mm (mm)
Recv: 
Recv: echo:; Filament settings: Disabled
Recv: echo:  M200 S0 D1.75
Recv: echo:; Steps per unit:
Recv: echo: M92 X80.35 Y80.35 Z398.27 E392.50
Recv: echo:; Maximum feedrates (units/s):
Recv: echo:  M203 X500.00 Y500.00 Z6.00 E60.00
Recv: echo:; Maximum Acceleration (units/s2):
Recv: echo:  M201 X3000.00 Y2000.00 Z60.00 E3000.00
Recv: echo:; Acceleration (units/s2): P<print_accel> R<retract_accel> T<travel_accel>
Recv: echo:  M204 P2000.00 R3000.00 T2000.00
Recv: echo:; Advanced: B<min_segment_time_us> S<min_feedrate> T<min_travel_feedrate> J<junc_dev>
Recv: echo:  M205 B50000.00 S0.00 T0.00 J0.30
Recv: echo:; Home offset:
Recv: echo:  M206 X0.00 Y0.00 Z0.00
Recv: echo:; Auto Bed Leveling:
Recv: echo:  M420 S0 Z0.00
Recv: echo:  G29 W I0 J0 Z0.88690
Recv: echo:  G29 W I1 J0 Z0.86179
Recv: echo:  G29 W I2 J0 Z0.94298
Recv: echo:  G29 W I3 J0 Z1.17230
Recv: echo:  G29 W I4 J0 Z1.36229
Recv: echo:  G29 W I0 J1 Z0.88606
Recv: echo:  G29 W I1 J1 Z0.87016
Recv: echo:  G29 W I2 J1 Z1.00659
Recv: echo:  G29 W I3 J1 Z1.16226
Recv: echo:  G29 W I4 J1 Z1.29199
Recv: echo:  G29 W I0 J2 Z0.89276
Recv: echo:  G29 W I1 J2 Z0.85677
Recv: echo:  G29 W I2 J2 Z0.96557
Recv: echo:  G29 W I3 J2 Z1.09949
Recv: echo:  G29 W I4 J2 Z1.23173
Recv: echo:  G29 W I0 J3 Z0.92289
Recv: echo:  G29 W I1 J3 Z0.87937
Recv: echo:  G29 W I2 J3 Z0.96557
Recv: echo:  G29 W I3 J3 Z1.08358
Recv: echo:  G29 W I4 J3 Z1.19071
Recv: echo:  G29 W I0 J4 Z0.95888
Recv: echo:  G29 W I1 J4 Z0.88021
Recv: echo:  G29 W I2 J4 Z0.95637
Recv: echo:  G29 W I3 J4 Z1.04257
Recv: echo:  G29 W I4 J4 Z1.11790
Recv: echo:; Endstop adjustment:
Recv: echo:  M666 Z0.00
Recv: echo:; PID settings:
Recv: echo:  M301 P22.16 I1.95 D63.07
Recv: echo:  M304 P87.81 I12.18 D422.02
Recv: echo:; Z-Probe Offset (mm):
Recv: echo:  M851 X29.00 Y-15.00 Z-2.25
Recv: echo:; Linear Advance:
Recv: echo:  M900 K0.47
Recv: echo:; Filament load/unload lengths:
Recv: echo:  M603 L665.00 U670.00
Recv: echo:; Filament runout sensor:
Recv: echo:  M412 S1
Recv: ok